VMC
Splined hub/boss for VMC clutch 10 springs ERGAL for Vespa PX125/150/200 E '95->/'98/MY/'11/Cosa 2
Vespa 125 VNB/GT/GTR/TS/PX
Vespa 150 VBB/GL/Sprint/Sprint Veloce/PX
Vespa 200 PE
Gasket for exhaust hole 36 mm VMC SEIDUE KIFLY- Vespa 125 Primavera ET3-PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK /S/ XL
Reed valve intake manifold VMC with 2 holes d.28/30 for Vespa 50/90/125 Special-N-L-R-Primavera- ET3
Vespa 50 V5A1T N,L,R
Vespa 50 Special
Vespa 50 PK S (2 holes)
Vespa 125 Primavera VMA2T
Vespa 125 Primavera VMB1T
Sleeve attack (diameter 34mm)
For carburetors PHBH 28-30/VHSH 30
Vespa 50/90/125/150/160/180/200
Helmet Support Bracket VMC under seat for 50 special / Primavera Et3 frames
With this small support, helmets can be attached in a convenient position and, combined with a seat with a lock, helmets can be kept in a more protected position from potential wrongdoers.
Made of 3mm thick stainless steel, it should be screwed onto the seat hinge.
Check that the fastening screws are long enough before installing it.
VMC TOURING exhaust painted in Black for Vespa 125 Primavera-Primavera ET3
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
VMC SILURO TOURING Exhaust for Vespa Small frame
The exhaust has been designed and developed to be super performing while maintaining a classic and original look and sound.
It is entirely built from stamped steel sheets and assembled by craftsmen welders with decades of experience in making 2T exhausts.
The VMC SILURO "TOURING" version has a 28mm diameter exhaust flange and slotted mounting holes that adapt to cylinders with stud spacing of 52, 56, and 60mm. The final db killer has a smaller diameter than the one mounted on the Sport, specifically designed for the Touring model, but interchangeable with the Sport model if you want to improve performance.
It fits very well on cylinders with a 27/28mm exhaust hole like the new Vmc CP-58, the classic original 125, the 130 Polini in cast iron, Malossi, Quattrini M1, Dr, Pinasco and also on short-stroke cylinders like the Vmc T-56 106cc or the VMC 100 RVA reed valve to the cylinder or the various Polini Malossi 105cc / 115cc
<
Coil support bracket and VMC voltage regulator for Vespa 50/90/125 Special/N-L-R-Primavera-PK
Vespa 50/90/125 Special/N-L-R-Primavera-PK
Support Plate for control unit and voltage regulator to be mounted on Vespa small frame engine casing
With this support made of stainless steel, it is possible to
mount the coil and the voltage regulator directly on the
Vespa small frame engine casing
VMC multifunction tool clutch/flywheel puller and spring compressor for Vespa 50/90/125/Primavera//ET3/PK50-125/S/XL/XL2
Vespa 50 V5A1T N,L,R
Vespa 90 V9A1T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa PK
VMC 2.0 Multifunction Extractor Tool
Professional multifunction tool, designed for quick and safe operations on Vespa Smallframe engines. The 2.0 version introduces structural improvements for greater efficiency and durability.
Main functions:
✅ VMC flywheel extractor with M22 x 1.5 thread
✅ Smallframe clutch extractor with original threading
✅ Clutch spring compressor, allows clutch disc replacement without removing the internal hub from the cluster.
Made of high-strength steel
Product made in Italy
Thermal group VMC RV-A 100 (100cc) for Vespa 50 V5A1T N/L/R/50 Special V5A2
Vespa 50 V5A1T N,L,R, Vespa 50 Special V5A2>3T, Vespa 50 Special V5B1>4T, Vespa 50 PK, Ape 50
VMC has developed a superior class cylinder with this lamellar to the RV-A 100 cylinder.
The technical solutions on this cylinder allow performances that were previously reserved for long-stroke cylinders.
The cylinder is made of aluminum with a Nikasil coated barrel and lamellar intake.
The head is CNC machined, with a viton gasket and secured with eight M6 bolts.
It has a bore of 54 mm and a stroke of 43 mm, 8 transfers
Exhaust port with bridge with an outlet diameter of 28 mm and stud spacing of 52 mm
Phases 113° intake and 171° for the exhaust
The manifold has an internal diameter of 25 mm and is equipped with a four-petal reed pack.
Included in the kit are the original valve closure cap screw kit and gasket kit in paper of different thicknesses.
Recommended carburetor sizes: 19 - 24 mm
VMC SILURO SPORT Exhaust for Vespa 50 PK S/XL/N/HP/FL (long stroke) - 125 PK S/XL/N/HP/FL
Vespa 50 PK S/XL/N/HP/FL
VMC SILURO SPORT Exhaust for Vespa PK
The VMC SILURO SPORT is a high-performance exhaust, specifically designed for Vespa PK frames. It combines high performance with a classic design and sound that remains faithful to the original aesthetics.
Construction Features:
-Entirely made from stamped steel sheets
-Handcrafted assembly performed by specialized welders with over ten years of experience in building exhausts for 2T engines
-Exhaust flange with a diameter of 32 mm
-Slotted mounting holes, compatible with cylinders having stud spacing of 52, 56, and 60 mm
Compatibility:
Optimized for pairing with high-performance cylinders, including:
VMC GS in cast iron
VMC ET6 and ET7 in aluminum (135cc and 144cc)
Pinasco Zuera
Quattrini M1 Series (M1 56-60, M1-60B, M1L 56-60)
EGIG 170cc in cast iron
...and other cylinders of
Kit of sheaths and wires to measure VMC with adjustments on gear cables for Vespa 50/90/125 Primavera ET3
Vespa 50/90/125 Primavera ET3
Thermal group VMC GS 56 125cc Ø 56mm for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 ETS
Vespa 125 PK
Bore diameter 56mm
Stroke 51mm
Displacement 126cc
Timing: Main transfers 124° Exhaust 174°
High silicon content aluminum alloy dual-ring piston.
Die-cast aluminum head, Steel rings, Steel pin, Steel retainers
Recommended squish 1.2 mm Bolt tightening m6 11-12 Nm, nuts m7 1.4-1.5 Nm
It mounts with crankshafts stroke 51mm and rod 97mm
Attention: To be mounted on Piaggio crankcases, a small modification on the half-moon is needed as the cylinder has been designed with generous fluid dynamics that require more space at its base.
Reinforced clutch key VMC (Steel 39NiCrMo3) for Vespa 50/90/125/Primavera/ET3/PK50-125/S/XL-flywheel side GS 150-160
Vespa 50 V5A1T N,L,R (clutch side)
Vespa 50 Special V5A2>3T (clutch side)
Vespa 50 Special V5B1>4T (clutch side)
Vespa 90 V9A1T (clutch side)
Vespa 125 Primavera VMA1T>2T (clutch side)
Vespa 125 Primavera ET3 VMB1T (clutch side)
Vespa PK (clutch side)
Vespa 150 GS VS1T>5T (clutch and flywheel side)
Vespa 180 SS VSC1T
Dimensions: 9.4 x 3.3 x 3
Base gasket thickness 0.5mm VMC CRONO cylinder kit Vespa 125/150 Sprint V-GTR-TS-PX
Vespa 125 PX
Vespa 125 GT/GTR/TS
Vespa 125 Cosa
Vespa 150 PX
Vespa 150 Sprint Veloce
Vespa 150 Cosa
Vespa 50 V5A1T N,L,R from 1966
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 90 V9A1T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Reinforced VMC cross with thread type for Vespa 125 VM1/2T/VN1/2/VNAVNB/VL1
Vespa 125 VM1>2T
Vespa 125 VN1>2T
Vespa 125 VNA1>2T
Vespa 125 VNB1>5T
Vespa 125 Super VNC1T
Vespa 125 GT VNL2T
Vespa 125 GT R VNL2T
Vespa 150 VL1>3T
Vespa 150 VB1T
Vespa 150 VBA1T
Vespa 150 VBB1T
Vespa 150 VBB2T
Vespa 150 GL VLA1T
Vespa 150 Super VBC1T
Vespa 150 Sprint VLB1T
Vespa 150 Sprint Veloce VLB1T
Vespa 160 GS VSB1T
Vespa 180 Rally VSD1T
Vespa 180 SS VSC1T
Reinforced VMC BOMBATA OLD Cross for Vespa large frame VBB, VBA, VNB, Sprint, GS, GL
Made of special steel with related vacuum carburizing treatment with surface hardness of 56/60 HRC
A chamfer has been machined on the corners of the ends of the cross to preserve the integrity of the gears and the selector
The cross has slightly larger dimensions compared to the original ones, which may require small adjustments to be made on the wheel axle before assembly.
VMC EASY engine mount support for Vespa 50/90/125 N/L/R-Special-Primavera-PK
Vespa 50/90/125 N/L/R-Special-Primavera-PK
Base gasket thickness 0.5mm VMC ET6 and ET7 thermal group for Vespa 50 Special V5B3T/90 V9A1T-125 Primavera ET3-PK
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 ETS
Vespa 125 PK
VMC engine casing "X1" model ROTARY VALVE for Vespa 50/90/125 Primavera ET3 / PK
Vespa 50/90/125 Primavera ET3 / PK
Carter VMC X1 for Vespa Small Frame mod. ROTARY VALVE
The evolution of modifications in the Vespa world is constantly evolving, and VMC has also decided to create specific casings for Vespa small frame that can accommodate the most powerful thermal kits and larger displacements available on the market. VMC has designed and manufactured casings capable of meeting these needs and has given life to the VMC X1 Casings
The Vespa Smallframe VMC X1 Casings are made of aluminum alloy, cast in sand molds and CNC machined in Italy, and checked for dimensions with high precision instruments.
Compared to Piaggio casings and semi-standard aftermarket versions, VMC casings feature technical improvements that position them at a higher level and make them the essential base for those who want a safe product made by enthusiasts for enthusiasts.
The VMC X1 engine casings have the following technical features:
- innovative fastening system for removable gear wire rods, which, combined with our external rod gear sheaths, speeds up engine change and gear cable tension adjustment
- increased wall thickness for greater resistance to mechanical stress
- a very wide cylinder support base
Thermal group gasket kit VMC ET6 and ET7 for Vespa 50 Special V5B3T/90 V9A1T-125 Primavera ET3-PK
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 ETS
Vespa 125 PK
Matte black aluminum tubeless VMC rim 2.10/10 for Vespa 50-125/PV/ET3/PK/S/XL/XL2/125 GT-TS/150 GL/GS VS5T/Sprint/V/T4/Rally/PX/PE/Lusso/T5/LML Star/DLX/Deluxe 2T/4T
Vespa 50/80/90/125/150/160/180/200
Measure--> 2.10-10" with pre-installed valve
Usable with tires: - 3.00 x 10 - 3.50 x 10 - 90/90-10
Without Nuts
Lamellar intake manifold VMC with 2 holes d.28/30 for Vespa 50/90/125 Special-N-L-R-Primavera- ET3
Vespa 50 V5A1T N,L,R
Vespa 50 Special
Vespa 50 PK S (2 holes)
Vespa 125 Primavera VMA2T
Vespa 125 Primavera VMB1T
Sleeve diameter 30 mm
for carburetor: PHBL PHBH -22 - 24 - 25
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK /S/ XL
Hole 34mm
VMC CRONO thermal group gasket kit for Vespa 125/150 Sprint V-GTR-TS-PX
Vespa 125 PX
Vespa 125 GT/GTR/TS
Vespa 125 Cosa
Vespa 150 PX
Vespa 150 Sprint Veloce
Vespa 150 Cosa
7-port aluminum cylinder with Nikasil-coated bore and exhaust "Booster".
Bore diameter 63mm, stroke 57mm, displacement 177cc,
main transfer phases 117°, exhaust 177°. Meteor dual-ring aluminum alloy piston
Die-cast aluminum head with 8 fixing points with recessed squish band
Steel rings. Steel pin. Steel retainers.
Cylinder gaskets in paper/aluminum.
Zinc-plated steel exhaust manifold bolted with Viton O-ring gasket.
Racing Exhaust Printed VMC EVO RACER 52 - S for Vespa 125 New VMA1T/125 Primavera VMA2T/ET3 VMB1T
Vespa 125 Primavera, Vespa 125 Primavera ET3
Mounts on Et3 frames with the side compartment, on Pk frames it is necessary to slightly cut the bulkhead to allow the expansion curve to pass through.
On pre-1976 Primavera frames, the compartment is deeper and may limit the installation of the exhaust.
Designed to give the best performance on 125/185 timing, it adapts to a wider range of timings.
It fits very well with long-stroke 130cc cylinders that have a 32mm exhaust diameter.
VMC TORK B expansion exhaust for Vespa 50/90/125 Primavera-ET3-PK
Vespa 50 Special-N-L-R (adaptable)
Vespa 50 PK (adaptable, removing spare wheel holder)
Vespa 125 Primavera/ET3
52/62 mm
Piston 56 (55, 945) dual-ring VMC GS 56 Sel. 00 for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 ETS
Vespa 125 PK
Complete VMC Pro CUP 2 piston with a diameter of 56 for Vespa 50 Special/NLR/Primavera/ET3
VMC Pro CUP 2