Malossi
Malossi BIG DEPS Ø47 aluminum thermal group pin Ø10 for Piaggio Ciao/Ciao PX
Hello/Hello PX
The only cylinders on the market for CIAO/SI with split exhaust
and symmetrical ports!!!!
The exhaust fitting is screwed on and offers two major
advantages:
Extreme durability and the possibility of replacement in case of breakage
Possibility to enlarge the exhaust outlet, further
increasing performance
These results have been made possible by the decompression valve
provided in the kit, which is smaller than the original
Piaggio one.
The most important innovation is represented by the completely redesigned
internal porting
specifically studied to achieve cylinder flushing
maximizing power at the correct operating speed.
Note: On the original Piaggio engine case, boring is necessary.
Reed valve manifold to the PHBH 30 crankcase for Vespa 125/150 VNB-GT-GTR-TS-Sprint-Sprint V-GTR-TS-PX
Vespa 125 PX
Vespa 125 GT/GTR/TS
Vespa 125 Cosa
Vespa 150 PX
Vespa 150 Sprint Veloce
Vespa 150 Cosa
RED FILTER E9 air filter with Ø 51 for SHA 12 / 10 - 12 / 12 - 13 / 13 carburetors
for carburetors SHA 12 / 10 - 12 / 12 - 13 / 13
Ø filter thread: 51mm
Vespa 50/90/125/150/200
- High-quality material
- Weather-resistant, UV-resistant, and ozone-resistant
- Reinforced internal flange to support the hand and neutralize vibrations
- Smooth outer surface to ensure greater safety
- The UP marking on the outer part (side grip) allows you to identify the orientation for correct assembly - Anatomical shape and structure, 30 mm diameter
In each package, you will find a complimentary folder of MINI Malossi stickers!
Vespa 200 Rally VSE1T
Vespa 200 PE VSX1T
Vespa 200 Cosa VSR1>2T
Bore: 68.5 mm
Stroke: 60 mm
Long reach spark plug
Malossi TOO BAD exhaust with enlarged Ø27 attachment for Ciao-Ciao PX
Yes-Hello-Good
Attention: enlarged Ø27 attack (only for BIG DEPS Malossi cylinders or equivalents.)
Roller bearing gearbox shaft MALOSSI 29x35x13 mm for Vespa 125 GT 2°/GTR/Super 2°/TS/150 GL 2°/Sprint 2°/V/Super 2°/Rally/PX80-200/PE/Lusso/T5/Cosa
Vespa 125 Super VNC1T 024900>
Vespa 125 GT VNL1T 60900>
Vespa 125 GTR VNL2T
Vespa 125 TS VNL3T
Vespa 125 PX VNX1>2T
Vespa 125 PX T5
Vespa 150 Super VBC1T 70200>
Vespa 150 Sprint VLB1T 73900>
Vespa 150 Sprint Veloce VLB1T
Vespa 150 PX VLX1T
Vespa 180 Rally VSD1T
Vespa 200 Rally VSE1T
Vespa 200 PE VSX1T
Measurements: 29x35x13 mm
Primary couple with extended Malossi ratio (Z 23/64) for Vespa 200 PX-Rally-Cosa
Vespa 200 Rally VSE1T
Vespa P 200 E VSX1T
Vespa PX 200 E VSX1T
Vespa PX 200 E Rainbow VSX1T
Vespa PX 200 E Rainbow Elestart VSX1T
Vespa 200 PE VSX1T Millennium '98
HTQ Malossi gears for Vespa PX inherit the legacy of the first gear project produced by Malossi between the late 80s and early 90s.
Completely redesigned, this pair of primary gears uses a straight-tooth configuration instead of the standard helical gears.
Malossi has worked hard to ensure the exceptional quietness of the gears, achieved with special machining of the teeth and their contact surfaces, meticulously finished and verified with an involute tester.
HTQ Malossi gears are made using exclusively materials
that exceed the strict standards imposed by our technicians with rigorous tests and trials.
The final machining uses CNC machines, after which the HTQ Malossi gears undergo a complete thermochemical carburizing treatment at 900°C, giving them the required hardness and
resistance.
The size and quality of the finished gears are finally verified on Zeiss three-dimensional control machines.
Paired in pairs to ensure the correct operating clearance, HTQ Malossi gears are the most precious gift a true romantic enthusiast can give to their Vespa.
Variator rollers MALOSSI HT Roll 19x15.5 mm 7.5 g for Vespa ET2/ET4/LX/LXV/S, 50cc 2T/4T AC/LC
Vespa ET2/ET4/LX/LXV/S, 50ccm 2T/4T AC/LC
HTRoll
HIGH RESISTANCE CALIBRATED ROLLERS
for original variators and Multivar
HTRoll are made of CPT with a specific formula and
have the corresponding weight marked on one side.
HTRoll represent a technical replacement for the original and are
a complete series of calibration elements capable of varying the transmission
ratio of your scooter, perfectly adjusting its speed
and acceleration.
Operation
Due to rotation, the weight of the rollers transforms into centrifugal
force: the greater the weight of the roller, the greater the centrifugal force and
the shorter the shift time, and vice versa.
Variator calibration
To optimize engine performance, use rollers that during
use keep the engine in the maximum power rotation range.
By reducing the weight of the rollers, the engine increases the number of
operating revolutions, conversely, by increasing the weight of the rollers, the
number of revolutions decreases.
Transmission belt X-Special Belt (size 18.5x8x727 mm - angle 30°) for Vespa ET2/ET4/LX/LXV/S, 50ccm 2T/4T AC/LC
Vespa ET2/ET4/LX/LXV/S, 50cc 2T/4T AC/LC
The X Special Belt V-belts are the best choice to ensure performance and reliability for your scooter.
They are produced with compounds designed to ensure optimal resistance and traction, and their shapes have been fine-tuned to perfectly adhere to the surfaces of the automatic transmission components.
The X Special Belt is not only perfectly interchangeable with the original belt, but it also offers all the advantages of Malossi product quality.
Complete dual-ring piston Malossi MHR 130cc diameter 57.5 selection 0 for Vespa 50 Special/NLR/Primavera/ET3
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 ETS
Vespa 125 PK
Diameter 57.7 selection 0
Complete single-ring piston Malossi MHR 130cc diameter 57.5 selection 0 for Vespa 50 Special/NLR/Primavera/ET3
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 ETS
Vespa 125 PK
Diameter 57.7 selection 0
Malossi VR-ONE crankcase reed valve for Vespa 125/150 GT-TS-Sprint-GL-PX
Vespa 125/150 GT-TS-Sprint-GL-PX
The V-One is designed for those who want a perfectly
replaceable casing to the original, supplied with all the necessary components
for assembly and that allows maximum interchangeability with the
components available on the market, it does not require any aesthetic modification
of the vehicle and fits all original Piaggio parts
The bearing seats are designed to accept the original crankshaft bearings and seals (not supplied). V-One can be mounted with the
original Dell’Orto Si 24-24 carburetor. It is possible to use
the original crankshaft or our rotary valve crankshaft with a 57mm stroke art. 5316082. Whatever the choice,
the fuel system has been revised and enhanced thanks to our
modern CAD systems that have profiled an optimized intake duct in the casing. Entirely made in ITALY
Malossi Ø46.5 cast iron thermal group with Ø10 pin for Piaggio Ciao-SI-Bravo
Yes-Hello-Good
Attention: On original Piaggio crankcase, it is necessary to bore.
Malossi Clutch Disc Kit (3pcs) for Vespa 80/125/150 GT-GTR-TS-VNB-VBB-GL-Sprint-V-PX
Vespa 125 Super VNC1T
Vespa 125 TS VNL3T
Vespa 125 GT VNL1>2T
Vespa 125 GTR VNL2T
Vespa 125 PX VNX1T > VNX2T
Vespa 150 Super VBC1T
Vespa 150 Sprint VLB1T
Vespa 150 Sprint Veloce VLB1T
Vespa PX 150 E VLX1T > VLX2T
The MHR versions, specifically designed for competitions and the most demanding customers, have friction materials with mixtures free of cork and rubber that allow extreme use without issues of sticking and slipping.
PISTON Malossi Ø 61 SELECTION 0 WITH PIN Ø 15 AND 2 SEMI-TRAPEZOIDAL RINGS for Vespa 125/150 Sprint V-GTR-TS-PX
Vespa 125 PX
Vespa 125 GT/GTR/TS
Vespa 125 Cosa
Vespa 150 PX
Vespa 150 Sprint Veloce
Vespa 150 Cosa
Malossi intake manifold (carb SHB 16/16 mm) for Vespa 50/125 PX XL-ETS
Vespa 50 PK XL/N/HP
Vespa 125 PK XL/N/HP
Vespa 125 PK ETS VMS1T
for SHB 16.15/16.16
passage: 18mm
carburetor connection: 21.5mm
3 holes
rotary disc valve
Malossi PISTON Ø 68.5 SELECTION A WITH Ø 16 PIN AND 2 CHROMED SEMI-TRAPEZOIDAL RINGS
Vespa 200 Rally VSE1T
Vespa 200 PE VSX1T
Vespa 200 Cosa VSR1>2T
Vespa PE 200
Vespa 200 Rally VSE1T
Vespa 200 Cosa
Malossi power exhaust has been redesigned, increasing the power
compared to previous models by about 5%, thanks to an in-depth
study that involved the internal surfaces of the sheet metal with which the
expansion is made.
Painted in black
Vespa 125 ETS-PK XL
Oil seal dimensions:
Oil seal Ø 24x35x6 mm in FKM for the crankshaft on the transmission side
Oil seal Ø 22.7x47.05x7 mm in FKM for the crankshaft on the clutch side
Oil seal Ø 27x37x7 mm in FKM/PTFE for the wheel axle
Vespa PX 125 T5 VNX5T
Vespa PX 125 T5 Elestart VNX5T
Vespa 200 PX VSX1T
Vespa 200 Rally VSE1T
Vespa 200 Cosa VSR1T
kit composed of 4 cork discs, 3 metal discs, and 7 springs
Vespa PX disc brake from 2000
Measure as original
Complete carburetor SHBC 20/20 DELL'ORTO for Vespa 125 Primavera VMA1T/VMA2T-ET3
Vespa 200 Rally VSE1T
Vespa 200 PE VSX1T
Vespa 200 Cosa VSR1>2T
Pair of black Malossi GAS model grips for Vespa 50/90/125 Primavera ET3/GTR/Sprint V/TS/Rally/PX
Vespa 50/90/125/150/200
The importance of the grip has been known since the dawn of time.
Man has always sought to make the hold on tools and weapons secure and effective, without neglecting to personalize the grips, sometimes embellishing them with noble materials. Finally, from today, even your motorcycles can have something special: Malossi takes care of it!
The direct contact is almost never missing, the palm and fingertips grip the handle to transmit the command's impulse, sometimes gently, sometimes violently, depending on the temperament or mood of the moment, and the engine, with a sound that is music to the ears of all pilots who live the passion of driving, responds by developing the requested performance and transporting you into the wind.
Malossi grips have no rivals for riding your motorcycle:
they are safe, anatomical, and indestructible, and also charming, because the care of the image is never secondary for us!
Technical features:
High-quality material
Resistant to atmospheric agents, UV rays, and ozone
Reinforced inner flange to support the hand and neutralize vibrations
The UP inscription on the outer part (lateral grip) allows identifying the orientation for correct assembly
<
Clutch bell 7 springs "power up clutch" Malossi for Vespa 200 Rally-PE-Cosa
Vespa 200 Rally VSE1T
Vespa P 200 E VSX1T
Vespa PX 200 E VSX1T
Vespa PX 200 E Rainbow VSX1T
Vespa PX 200 E Rainbow Elestart VSX1T
Vespa 200 PE VSX1T Millennium '98
Vespa 200 Cosa VSR1T
High-strength steel with surface hardening treatment to increase wear resistance and, consequently, durability.
Reinforcement ring welded with TIG technique on the outer diameter of the bell to effectively counteract the centrifugal force developed by the higher rotational speed.
For original clutch and Malossi POWER UP CLUTCH SYSTEM.
Power Up Clutch Spring Holder Plate Malossi for Vespa 125 T5-200 Rally-PX
Vespa 180 Rally VSD1T 0014741>
Vespa 200 Rally VSE1T
Vespa 125 T5 VNX5T
Vespa 125 Cosa VNR1T
Vespa 150 Cosa VLR1T
Vespa 200 Cosa VSR1T
Vespa 200 PE VSX1T
TECHNICAL FEATURES:
Clutch base plate: Hardened steel, high toughness, optimal for components with highly dynamic stresses with a tensile strength of 1000 MPa. Surface hardened (LCN) to 300HB, depth 10-25 µm. Main spring seats machined with offset relative to the clutch bell to ensure intrinsic torque, eliminating any play. Auxiliary spring seats machined aligned with the clutch bell. Tight tolerances between the spring push disc tabs and the clutch bell eliminating clutch noise and increasing durability. Surface induction of the bronze bushing coupling section. Hardened to a depth of 1.5 mm, 60HRC, improving durability. For original clutch bell and POWER UP CLUTCH SYSTEM Malossi.
Power Clutch Spring Holder Plate Malossi for Vespa 125/150 PX-PE
Vespa 125 GTR VNL2T 145901>
Vespa 125 TS VNL3T 18139>
Vespa 125 Sprint Veloce VLB1T 294260>
Vespa 150 Super VBC1T 412374 >
Vespa 125 PX VNX1T
Vespa 150 VBX1T VBX1T
Vespa 80 PX V8X1T
Vespa 100 PX VIX1T
Vespa 125 PX VNX2T
Vespa 150 PX VLX1T
TECHNICAL FEATURES
Clutch base plate:
Tempered steel, high toughness, optimal for components with highly dynamic stresses with a tensile strength of 1000 MPa.
Surface hardened (LCN) to 300HB, depth 10-25 µm.
Main spring seats machined with offset relative to the clutch bell to ensure intrinsic torque, eliminating any play.
Auxiliary spring seats machined aligned with the clutch bell.
Tight tolerances between the spring push disc tabs and the clutch bell eliminating clutch noise and increasing durability.
Surface induction of the coupling area of the bronze bushing. Hardened to a depth of 1.5 mm, 60HRC, improving durability.
For original clutch bell and POWER UP CLUTCH SYSTEM Malossi.
Malossi elastic ring in high-toughness tempered steel clutch pack tightening for Vespa 125/150 VNB-GT-GTR-TS-PX-VBB-GL-Sprint-Sprint Veloce
Vespa 125 VNB/GT/GTR/TS/PX
Vespa 150 VBB/GL/Sprint/Sprint Veloce/PX
Elastic ring Malossi in high-toughness tempered steel clutch pack tightening for Vespa 200 PX-PE
Vespa 200 PE VSX1T
Vespa 200 Rally VSE1T
Vespa 200 Cosa VSR1T
Malossi 7 Springs Clutch Kit POWER UP CLUTCH SYSTEM for Vespa 200-PX-PE-Rally
Vespa 200 PE
Vespa 200 Rally
The Malossi range for the Vespa offers products with extremely high technology capable of developing performance increases
so exceptional compared to the standard, that it requires the adaptation of other fundamental components
of the vehicle.
Just compare a Vespa PX 200 E produced in 1978, which originally develops a power of 12.35 HP at 5700 RPM, with a Vespa "tuned" with Malossi Kits, which can develop 27.5 HP at 8000 RPM, or more than double
HP at an extremely higher rotation speed, to understand that it was absolutely essential to design a clutch unit capable of withstanding the stresses due to a performance increase of such proportions!
The POWER UP CLUTCH SYSTEM Malossi clutch units are designed to provide a response and overcome all the problems that inevitably arise when the clutch unit technology is not adequate to the other engine components. A traditional clutch, having to transmit more than double the power to the gears, while simultaneously rotating much faster, can lead to bell failures under the effect of
centrifugal force, slipping and deformations that translate into annoying and unsettling metallic noises, up to the classic clutch slipping caused by
Primary gear set with extended Malossi ratio (Z23-64) straight teeth with sprocket (8 springs) complete with shock absorber for Vespa 125/150/200 PX-PE-Rainbow-Disc brake-Cosa
Vespa 200 PE VSX1T Millennium '98
Vespa 200 Cosa VSR1T
The HTQ Malossi gears for Vespa PX inherit the legacy of the first gear project produced by Malossi between the late 80s and early 90s.
Completely redesigned, this pair of primary gears uses a straight-tooth configuration instead of the standard helical ones.
Malossi has worked hard to ensure the exceptional quietness of the gears, achieved with special machining of the teeth and their contact surfaces, meticulously finished and verified with an involute tester.
The HTQ Malossi gears are made using only materials that exceed the strict standards imposed by our technicians through rigorous tests and trials.
The final machining uses CNC machines,
after which the HTQ Malossi gears undergo a complete thermochemical carburizing treatment at 900°C, giving them the required hardness and strength.
The size and quality of the finished gears are finally verified on Zeiss three-dimensional control machines.
Primary gear set with extended Malossi ratio (Z24-63) straight teeth with sprocket (8 springs) complete with shock absorber for Vespa 125/150/200 PX-PE-Arcobaleno-Disc brake-Cosa
Vespa 200 PE VSX1T Millennium '98
Vespa 200 Cosa VSR1T
The HTQ Malossi gears for Vespa PX inherit the legacy of the first gear project produced by Malossi between the late 80s and early 90s.
Completely redesigned, this pair of primary gears uses a straight-tooth configuration instead of the standard helical ones.
Malossi has worked hard to ensure the exceptional quietness of the gears, achieved through special machining of the teeth and their contact surfaces, meticulously finished and verified with an involute tester.
The HTQ Malossi gears are made using exclusively materials
that exceed the very strict standards imposed by our technicians with rigorous tests and trials.
The final machining uses CNC machines,
after which the HTQ Malossi gears undergo a complete
thermochemical carburizing treatment at 900°C, giving them the
hardness and
resistance required.
The size and quality of the finished gears are finally verified on
Zeiss three-dimensional control machines.
Primary couple with extended Malossi ratio (Z 23/64) for Vespa 200 PX-Rally-Cosa
Vespa 200 Rally VSE1T
Vespa P 200 E VSX1T
Vespa PX 200 E VSX1T
Vespa PX 200 E Rainbow VSX1T
Vespa PX 200 E Rainbow Elestart VSX1T
Vespa 200 PE VSX1T Millennium '98
The HTQ Malossi gears for Vespa PX carry the legacy of the first gear project produced by Malossi between the late 80s and early 90s.
Completely redesigned, this pair of primary gears uses a straight-toothed configuration instead of the standard helical ones.
Malossi has worked hard to ensure the exceptional quietness of the gears, achieved through special machining of the teeth and their contact surfaces, meticulously finished and verified with an involute tester.
The HTQ Malossi gears are made using only materials that exceed the very strict standards imposed by our technicians with rigorous tests and trials.
The final machining uses numerically controlled machines, after which the HTQ Malossi gears undergo a complete thermochemical carburizing treatment at 900°C that gives them the required hardness and resistance.
The size and quality of the finished gears are finally verified on Zeiss three-dimensional control machines.
Paired two by two to ensure the correct operating clearance, the HTQ Malossi gears are the most precious gift a true romantic enthusiast can give to their Vespa.
Malossi straight-tooth primary transmission gear set Z 27x69 for Vespa 50/90/125 Special-N-L-R-Primavera-ET3-PK
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
The power developed by an engine, whether standard or modified, will be pointless if it is not transmitted to the wheels in the most efficient and effective way, without unnecessary friction and waste of mechanical energy.
Malossi, a leader in the production of high-performance components for the scooter world, has focused all its know-how by completely redesigning the primary transmission for the classic Vespa "small frame" to ensure that the maximum power is transformed into road performance.
The new Malossi primary transmission for the Vespa is a true concentration of engineering. From the highest quality materials to the attention to detail and the quality of mechanical processes, everything is brought to a very high level. From the bronze bushing to the clutch basket and gears, everything is worked separately to ensure that each individual component is produced according to the highest quality standard.
The core of the innovations introduced in this transmission is the new clutch bell, made from special solid steel and characterized by six slots for the clutch discs, all six "active" and designed to lock the discs. In this way, all mechanical play is minimized, as are vibrations and the consequent wear of the basket itself and the guide teeth of the discs.
The new primary transmission is also
Malossi Z 24x72 straight-tooth primary transmission gear set for Vespa 50/90/125 Special-N-L-R-Primavera-ET3-PK
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
The power developed by an engine, whether standard or modified, will be pointless if it is not transmitted to the wheels in the most efficient and effective way, without unnecessary friction and waste of mechanical energy.
Malossi, a leader in the production of high-performance components for the scooter world, has concentrated all its know-how by completely redesigning the primary transmission for the classic Vespa "small frame" to ensure that the maximum power is transformed into road performance.
The new Malossi primary transmission for the Vespa is a true concentration of engineering. From the highest quality materials to the attention to detail and the quality of the mechanical processes, everything is brought to a very high level. From the bronze bushing, to the clutch basket and the gears, everything is processed separately to ensure that each single component is produced according to the highest quality standard.
The heart of the innovations introduced in this transmission is the new clutch bell, made from special solid steel, characterized by six slots for the clutch discs, all six "active" and aimed at locking the discs. In this way, all mechanical play is reduced to a minimum, as well as vibrations and the consequent wear of the basket itself and the guide teeth of the discs.
<
Malossi "Vespower" Voltage Regulator 12V AC/DC for Malossi Electronic Ignitions
Vespa 125 VNB1>6T
Vespa 125 GT VNL2T
Vespa 125 GTR VNL2T
Vespa 125 TS VNL3T
Vespa 125 PX
Vespa 150 Sprint VLB1T
Vespa 150 Sprint Veloce VLB1T
Vespa 150 PX
Vespa 200 PE