360 Project garage
Rollbar tube reinforcement 360 Project Garage 2.1 for Vespa 50 V5A1T L/R-Special V5A2>3T/V5B1>4T-90 V9A1T/125 Primavera ET3- 50/125 PK-S-XL-N-HP-FL-80/125/150/160/180/200 PX-PE-Sprint-TS-GL-Rally-VNB-VBB
Vespa 50 V5A1T L/R-Special V5A2>3T/V5B1>4T-90 V9A1T/125 Primavera ET3 Vespa 50/125 PK-S-XL-N-HP-FL
Vespa 80/125/150/160/180/200 PX-PE-Sprint-TS-GL-Rally-VNB-VBB
Reinforcement bar for Vespa Smallframe Frame 2.1 360 PG CNC
Specific reinforcement bar for the Vespa Smallframe frame, designed to improve structural rigidity while maintaining the correct elasticity of the frame.
The 360 PG CNC bar allows for adjusting the tension or compression of the frame cradle, enabling you to adapt the reinforcement to your needs without compromising the structure's flexibility.
Installation is done via front fastening in the holes intended for the spare wheel support and rear fastening at the height of the bag hook.
Finish and materials: Polished steel and CNC machined aluminum
WARNING: For the rear fastening, 2 holes must be made on the frame.
Reinforcement tube roll bar 360 Project Garage 2.2 for Vespa 50 V5A1T L/R-Special V5A2>3T/V5B1>4T-90 V9A1T/125 Primavera ET3
Vespa 50 V5A1T L/R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 90 V9A1T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa Smallframe Frame Reinforcement Bar 2.2 360 PG CNC with Under-Seat Bracket
Compatible with Vespa 50 Special, 125 ET3, Primavera, 50 L, N, and R.
Specific reinforcement bar for the Vespa Smallframe frame, designed to enhance structural rigidity while maintaining the correct elasticity of the frame.
The 360 PG CNC bar allows you to adjust the tension or compression of the frame cradle, enabling you to adapt the reinforcement to your needs without compromising the flexibility of the structure.
Installation is done through front fixing in the holes intended for the spare wheel support and rear fixing on the seat hinge mounts, thanks to the special under-seat bracket.
Finish and materials: Polished in steel and CNC machined aluminum
Pair of "360 PG" frame side reinforcements for Vespa 50/90/125 Special-N-L-R-Primavera-ET3
Vespa 50/90/125 Special-N-L-R-Primavera-ET3
Reinforcement designed to increase rigidity and robustness in the engine pin locking area
Reinforced straight teeth primary transmission pair Z 29x68 "360 PG" for Vespa 50 N/L/R-Special-90/125/Primavera/ET3/PK50/125/S/XL/N/HP-Ape 50
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Primary gear 29/68 straight teeth, composed of 360 Project Garage steel shock absorbers, nitrided and balanced steel clutch basket, gear crown machined to accommodate BLU SHOCK springs by 360 PG. Prepared and assembled by 360PG
Primary reinforced straight-tooth transmission gear Z 27x69 "360 PG" for Vespa 50 N/L/R-Special-90/125/Primavera/ET3/PK50/125/S/XL/N/HP-Ape 50
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Primary gear 27/69 straight teeth, composed of 360 Project Garage shock absorber in solid steel, nitrided and balanced steel clutch basket, gear ring gear machined to accommodate BLU SHOCK springs by 360 PG. Prepared and assembled by 360PG
Reinforced straight teeth primary transmission gear Z 24x72 "360 PG" for Vespa 50 N/L/R-Special-90/125/Primavera/ET3/PK50/125/S/XL/N/HP-Ape 50
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Primary gear 24/72 straight teeth, composed of 360 Project Garage shock absorber in solid steel, nitrided and balanced steel clutch basket, gear crown machined to accommodate BLU SHOCK springs by 360 PG. Prepared and assembled by 360PG
Reinforced blue shock absorber spring kit -360 PG- for Vespa 50/125 Special-Primavera-ET3
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Kit of 4 reinforced shock absorber springs Blue-shock, 360 PG. Designed to be installed on all commercial bell housings equipped with shock absorber seats.
CNC quick throttle handlebar tube Vespa 50 Special, 50 L, N, R
Vespa 50 V5A1T N/L/R
Vespa 50 Special V5B3T
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera ET3
Vespa 125 PK
Vespa 125/150/200 PE
CNC Vespa 50 Special, 50 L, N, R handlebar stem rapid throttle modification 360 PG in solid aluminum. The stem body has been designed so as not to make structural changes to the handlebar during installation, the stem has two fixing points, one at the extreme part of the handlebar body, underneath the tube support clamp, and one inside the handlebar (headlight area). The front brake cable passage is the same as the original tube.
Short Manifold M1L Quattrini "360 PG" for Ape 50 P-TM-FL-FL2-FL3-RST MIX
Short Manifold M1L Quattrini for APE, made of steel, complete with gasket.
Short Manifold APE for PHBL 24 AD carburetor Male/Female connection for Ape 50 P-TM-FL-FL2-FL3-RST MIX
Short APE Manifold for PHBL 24 BS carburetor Male/Male connection for Ape 50 P-TM-FL-FL2-FL3-RST MIX
Short APE Manifold for PHBH 28 BS, VHST, PWK carburetor Male/Male connection for Ape 50 P-TM-FL-FL2-FL3-RST MIX
8 mm cylinder base "360 PG" for Vespa PX200/COSA200/Rally200
Vespa 200 Rally VSE1T
Vespa P 200 E VSX1T
Vespa PX 200 E VSX1T
Vespa PX 200 E Rainbow VSX1T
Vespa PX 200 E Rainbow Elestart VSX1T
Vespa 200 PE VSX1T Millennium '98
Vespa 200 Cosa VSR1T
Specification for Largeframe thermal groups stroke 60 connecting rod 110 mm
Pair of spacers for fixing electronic ignition control unit / coil L 22 mm hole 6 mm "360 PG"
Pair of gear selector shoes "360 PG" for Vespa 50-125/PV/ET3/PK50-125/S/XL/XL2
Vespa 50-125/Primavera/ET3
Vespa 50-125 PK/S/XL/XL2
Kit 2 Reinforced Smallframe gear selector shoes 360 Project Garage. Made of high-performance mechanical steel, revised in tolerance dimensions and sizes. Surface hardening heat treatment designed for greater durability over time, usage stress minimized, tested in competitions and sporty touring use.
Aluminum bushing for adapting VHSH 30 carburetor on enlarged manifolds, external diameter 44.5 mm 360 PG for Vespa 50/125 GT/GTR/TS-150 Sprint/S.Veloce/GL-160 GS/180 SS/Rally-200 Rally-Special-N-L-R-Primavera-PK
Aluminum bushing for VHSH 30 carburetor adaptation on enlarged manifolds, external diameter 44.5 mm 360 PG
No structural modifications to the carburetor are required, it is simply mounted by heating the bushing with a hairdryer and inserting it by hand.
Central stand risers L 28mm "360 PROJECT GARAGE" for Vespa 50/125 GT/GTR/TS-150 Sprint/S.Veloce/GL-160 GS/180 SS/Rally-200 Rally-Special-N-L-R-Primavera-PK
Vespa 125 GT VNL1>2T
Vespa 125 GTR VNL2T
Vespa 125 TS VNL3T
Vespa 150 GL VLA1T
Vespa 150 Sprint VLB1T
Vespa 150 Sprint Veloce VLB1T
Vespa 160 GS VSB1T
Vespa 180 SS VSC1T
Vespa 180 Rally VSD1T
Vespa 200 Rally VSE1T
Indispensable during the conversion of Smallframe Vespas from 9" to 10" wheels. They represent the ideal solution even when replacing the original fork with models derived from scooters (e.g. Zip SP, ET2, ET4, etc.).
Hai visualizzato 17 di 17 prodotti