Cylinder gasket kit QUATTRINI for racing cylinder M1X 172 cc (thickness): 0.3/0.5mm for Vespa 125 GTR 2°/TS/150 Sprint 2°/V/Super 2°/PX125-150/PE/Lusso/Cosa
for Vespa 125 GTR 2°/TS/150 Sprint 2°/V/Super 2°/PX125-150/PE/Lusso/Cosa
Related articles
Primary transmission gear pair Z 24x61 for Vespa 50 N/L/R-Special-90/125/Primavera/ET3/PK50/125/S/XL/N/HP-Ape 50
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Z 24x61 with helical teeth
With shock absorbers
Gas-pressurized rear shock absorber (Nitrogen) with separate compensation reservoir.
Vespa 50 V5A1T N,L,R, Vespa 50 Special V5A2>3T, Vespa 50 Special V5B1>4T, Vespa 90 V9A1T, Vespa 125 Primavera VMA1T>2T, Vespa 125 Primavera ET3 VMB1T, Vespa 125 PX, Vespa 150 PX, Vespa 200 PX, Vespa PX Arcobaleno
Rear Shock Absorber
ADJUSTMENT
The continuously adjustable millimetric ring for spring preload and the knob with clicks (12 clicks) for Compression damping adjustment allow you to customize the suspension setting according to your needs and riding preferences.
135 cc Pinasco ZUERA processing kit, 28 Polini carburetor, VMC evo racer exhaust
Vespa 50 N
Vespa 50 L
Vespa 50 R
Vespa 50 Special
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 ETS
Vespa 125 PK
Kit composed of:
- Pinasco 135 cc Zuera thermal group
- NEWFREN primary transmission pair
- 28 Polini carburetor + manifold
- VMC evo racer handcrafted exhaust (printed version, not as in photo)
- Thermal group shroud
- Long studs
- Pinasco power clutch 12 springs
- Pinasco Flytech electronic ignition
- Pinasco anticipated crankshaft cone 19
Fabbri Racing "MOWER" Evo full circle crankshaft 87 mm, cone 20, rod 97, stroke 51 for Vespa 50/90/125 Primavera-ET3-PK
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK S/XL/N/HP
Full Shoulder Crankshaft with 83 mm shoulders, 51 mm stroke, 97 mm copper connecting rod, and 20 mm taper.
The use of a crankshaft with 83 mm shoulders does not require boring of the engine cases.
Fabbri Racing recommends using a 6204 bearing instead of the 6303 on the transmission side, paired with a specific oil seal measuring 27x47x6 mm.
Bearings and oil seals are not included in the kit and must be purchased separately.
The recommended balance factor for pistons with a diameter between 57 and 60 mm is between 45 and 50.
Technical specifications:
Flywheel side bearing seat diameter: 20 mm
Clutch side bearing seat diameter: 20 mm
Flywheel side oil seal seat diameter: 20 mm
Clutch side oil seal seat diameter: 27 mm
Weight: approximately 1.4 kg